Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Before
After
Before
AfterHorizontal Roller & Sliding Windows in Fort Lauderdale, FL | Winslow Windows & Doors
Horizontal Roller & Sliding Windows are among the most practical impact-rated openings we install in Fort Lauderdale. They run on a reinforced track, open side to side without swinging into a room or patio, and pair laminated impact glass with a frame built for South Florida wind loads. Homeowners and builders choose them for wide openings, condominium replacements, and single-family remodels where a clean sightline and easy operation matter. Winslow Windows & Doors supplies and installs these across our PGT, CGI, CWS, ES Windows, ECO, and Mr-Glass lines. Call (904) 913-5886 to schedule a free on-site measurement in Fort Lauderdale.
Product Overview - Horizontal Roller & Sliding Windows
This is our workhorse impact profile: laminated impact glass tested to withstand 140-mph winds and 9,500 lbs of wind-borne debris impact, gliding horizontally on a reinforced track. In Fort Lauderdale, where a sliding window often faces the strongest elevation of the house, that combination matters more than almost any other spec on the quote.
Sliding windows work especially well in ranch homes, mid-century builds, and coastal condos where wall space is wide but swing clearance is tight. The horizontal operation means no awkward reach over a counter, no sash swinging into a walkway, and no conflict with exterior landscaping. The frame itself, whether extruded aluminum or vinyl, carries the glass panel along a track engineered to stay true under repeated use and Hurricane season after hurricane season.
The product is available in 2-track and 3-track configurations. A 2-track slider typically gives you one fixed panel and one moving panel. A 3-track expands ventilation potential with two operable sashes sliding past a fixed center panel, which is popular in Fort Lauderdale bedrooms and living rooms that want maximum air movement on winter afternoons. Both configurations take the same impact glazing package, so the protection level does not drop when the opening gets wider.
Architecturally, the slider is a quieter profile than a casement or awning window. The frame lines are lean, the glass area is generous, and the hardware is discreet. That restraint helps it disappear into stucco, wood, or concrete block elevations, and it tends to photograph well in listings when a Fort Lauderdale homeowner goes to sell.
We install these systems throughout Broward County, and most of the sliders we replace in Fort Lauderdale were originally non-impact aluminum units from the 1980s and 1990s. The upgrade path from there to a code-compliant, NOA-rated sliding window is straightforward when the rough opening is measured properly and the new frame is set level, plumb, and square. Call (904) 913-5886 if you want to walk through what the swap would look like on your property.
Technical Specifications
- Frame materials: Extruded aluminum, vinyl
- Track configurations: 2-Track, 3-Track
- Glass options: Laminated impact glass with PVB interlayer, Low-E insulated glass, tinted glass, clear glass
- Finish options: White, Almond, Bronze, Black, Tan
- Screen options: Retractable screen, sliding screen
- Design pressure: Matched to your Fort Lauderdale wind zone, up to +/-100, never higher
- Compliance documentation: Miami-Dade NOA and Florida Product Approval numbers available per configuration, verified on your specific quote
- Code standard: Engineered to Florida Building Code (FBC) High-Velocity Hurricane Zone (HVHZ) requirements
Hurricane & Compliance Performance
Laminated Impact Glass
Two panes of glass are bonded to a PVB (polyvinyl butyral) interlayer. When a wind-borne object strikes, the glass may crack but the interlayer holds the broken pieces in place, keeping the building envelope sealed and blocking wind and water intrusion. This is the core protective mechanism in every impact slider we supply in Fort Lauderdale.
Miami-Dade NOA / Florida Product Approval
Each configuration carries its own Miami-Dade Notice of Acceptance and Florida Product Approval numbers. The numbers are configuration-specific, not a single blanket approval, so we verify the exact NOA and FL approval for your size and options on your written quote. Your Fort Lauderdale permit submittal relies on that documentation being correct.
FBC / HVHZ Compliance
The system is engineered to Florida Building Code High-Velocity Hurricane Zone requirements. HVHZ governs Broward County and the rest of South Florida, and it is a stricter standard than what inland parts of the state follow. Fort Lauderdale sits squarely inside that HVHZ map.
TAS 201 / TAS 202 / TAS 203 Testing Context
HVHZ-rated impact products are tested under the TAS protocol family. TAS 201 covers large-missile impact, TAS 202 covers cyclic wind-pressure loading, and TAS 203 covers forced-entry resistance. These are the tests a product must pass before it can carry a Miami-Dade NOA, and they are the reason an impact slider behaves differently from a standard insulated window.
Design Pressure for Your Wind Zone
Design pressure is matched to your specific wind zone, up to +/-100, never higher. We do not oversell a higher DP rating than your location requires, because the right number is the one that pairs correctly with your opening size, frame material, and elevation. Over-rating a window adds cost without adding meaningful protection; under-rating fails inspection.
Energy Performance
Low-E and insulated glass options are available for energy performance. In a Fort Lauderdale summer, Low-E coatings reduce solar heat gain through the glass while still allowing the laminated impact component to do its job. The glazing stacks can often be combined, so you get impact resistance and glass-coating performance in one unit.
Color & Glass Options
The finish palette for Horizontal Roller & Sliding Windows runs White, Almond, Bronze, Black, and Tan. Fort Lauderdale architecture splits fairly cleanly along these lines. White and Almond read traditional on 1970s concrete-block homes and Mediterranean stucco elevations. Bronze and Black carry a more modern, coastal-contemporary look, especially against lighter exterior walls or on homes in Victoria Park, Rio Vista, and along the Intracoastal. Tan sometimes splits the difference when a homeowner wants warmth without the starkness of pure white.
Glass selection follows function. Laminated impact glass with the PVB interlayer is the hurricane-rated baseline, available in clear form when you want the purest view. Tinted glass cuts glare without a visible coating, which helps on western-facing sliders that catch the afternoon sun over the Everglades. Low-E insulated glass adds thermal performance and is available on qualifying configurations for Fort Lauderdale homeowners who want the energy benefit plus the impact rating. Your quote should specify exactly which glass package the unit is built with, since the PVB interlayer and any Low-E coating each serve a different purpose.
Installation by Winslow Windows & Doors in Fort Lauderdale
An impact slider is only as good as the installation around it. The laminated glass does its job in the frame, but the frame has to be anchored, sealed, and squared correctly or the whole assembly falls short of the NOA-rated performance it was designed for. That is why Winslow Windows & Doors treats installation as a compliance process, not a swap-out.
Every Fort Lauderdale project starts with a pre-install inspection. We measure the rough opening, check the condition of the surrounding framing, and review the existing anchorage before ordering anything. When the new unit arrives, it is set level, plumb, and square, then anchored to the structure according to the manufacturer’s approved installation instructions for that specific configuration. The perimeter is sealed with AAMA 812 low-expansion foam, and our installation practice follows AAMA 2400/2410 standards for flashing and integration with the wall assembly.
After the window is set, we run a water test on the perimeter and inspect the operation of every moving sash. Then we clean the work area and walk you through the hardware, the locking points, and the screen operation before we leave. In Fort Lauderdale’s coastal exposure zones, the anchoring and sealant details matter just as much as the glass, because water intrusion at the rough opening causes more long-term damage than almost anything else we see on older homes.
Permitting awareness is part of the process in HVHZ jurisdictions like Fort Lauderdale. The NOA or Florida Product Approval numbers have to match the windows on the permit set, and the product has to be installed in a manner consistent with the approved drawings. Improper installation compromises the NOA-rated system, and a failed inspection on a replacement window job is usually traced back to a unit that was measured wrong, anchored wrong, or documented wrong. We manage that paperwork as part of the job. Call (904) 913-5886 to schedule a site visit and get a written quote on your Fort Lauderdale slider project.
Frequently Asked Questions - Horizontal Roller & Sliding Windows
Design pressure is matched to your specific Fort Lauderdale wind zone, up to +/-100, never higher. The exact DP rating on your quote depends on the opening size, frame material, track configuration, and the elevation of the wall where the window sits. The impact glazing itself is tested to withstand 140-mph winds and 9,500 lbs of wind-borne debris impact. We verify the correct design pressure for your address before ordering, so the unit you buy is the right one for your building’s exposure, not a generic maximum rating. Call (904) 913-5886 for an exact quote, estimates are free.
Lead times depend on the manufacturer line you choose, the glass package, and the frame finish. PGT, CGI, CWS, ES Windows, ECO, and Mr-Glass each run different production schedules, and a custom size with Low-E insulated glass can extend the timeline further. We confirm the current production window when we quote your project and keep you updated if the schedule moves. If your Fort Lauderdale project is permit-driven or tied to a contractor’s schedule, let us know during the estimate so we can plan the order date around it.
Yes, in Fort Lauderdale and other HVHZ jurisdictions, the permit application for impact windows typically requires the Miami-Dade NOA and Florida Product Approval documentation that matches the exact windows being installed. The numbers are issued per configuration, not as one universal approval, so we pull the correct documentation for your specific sizes, glass package, and frame options and include it with your submittal package. Submitting the wrong approval document is a common cause of permit delays on window replacements, and we handle that step for you.
Most Horizontal Roller & Sliding Windows can be custom-sized within the manufacturer’s approved range, and the approval documents have to match those actual dimensions. The 2-track and 3-track configurations give you flexibility in how many panels move, and the glass package, finish color, and screen type are all selected per opening. We measure every opening on-site before ordering, because a custom width slider that arrives a half-inch off can sit in a warehouse while the opening stays open. Call (904) 913-5886 and we will measure your openings and price the exact sizes you need.
Keep the bottom track clear of sand, leaves, and debris, especially after the wind blows through Fort Lauderdale in the summer. Rinse the track with water, wipe the frame with mild soap, and avoid abrasive cleaners on any finish. Lubricate the rollers or glides according to the manufacturer’s recommendation for your specific line. If a sash starts to drag or bind, do not force it, that usually means debris in the track or a roller that needs attention, and a service call is cheaper than replacing a damaged frame member.
Get a Quote - Horizontal Roller & Sliding Windows in Fort Lauderdale
We measure, quote, document, and install impact sliders in Fort Lauderdale every week. If you are replacing old aluminum windows or building new, call (904) 913-5886 to schedule a free on-site measurement. We will walk the openings, talk through glass and finish options, and give you a written quote with the correct NOA documentation for your permit set.
Written by the team at Winslow Windows & Doors, serving Fort Lauderdale with hurricane-impact windows and doors.
Six Reasons Homeowners Choose Winslow Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.
Other Winslow Windows & Doors Services
What Neighbors Say About Winslow Windows & Doors
Detailed Images
